收藏本站
CAT24M01
READ OPERATIONS
Immediate Address Read
In standby mode, the CAT24M01 internal address counter
points to the data byte immediately following the last byte
accessed by a previous operation. If that ‘previous’ byte was
the last byte in memory, then the address counter will point
to the 1st memory byte, etc.
When, following a START, the CAT24M01 is presented
with a Slave address containing a ‘1’ in the R/W bit position
(Figure 10), it will acknowledge (ACK) in the 9th clock cycle,
and will then transmit data being pointed at by the internal
address counter. The Master can stop further transmission by
issuing a NoACK, followed by a STOP condition.
Selective Read
The Read operation can also be started at an address
different from the one stored in the internal address counter.
The address counter can be initialized by performing a
‘dummy’ Write operation (Figure 11). Here the START is
followed by the Slave address (with the R/W bit set to ‘0’)
and the desired two byte address. Instead of following up
with data, the Master then issues a 2nd START, followed by
the ‘Immediate Address Read’ sequence, as described
earlier.
Sequential Read
If the Master acknowledges the 1st data byte transmitted
by the CAT24M01, then the device will continue
transmitting as long as each data byte is acknowledged by
the Master (Figure 12). If the end of memory is reached
during sequential Read, then the address counter will
‘wrap ? around’ to the beginning of memory, etc. Sequential
Read works with either ‘Immediate Address Read’ or
‘Selective Read’, the only difference being the starting byte
address.
BUS ACTIVITY: A
S
T
MASTER R
T
SDA LINE S
SLAVE
ADDRESS
S
T
O
P
P
A
C
K
DATA
N
O
A
C
K
SCL
SDA
8
8th Bit
9
DATA OUT
NO ACK
STOP
Figure 10. Immediate Address Read Timing
BUS ACTIVITY: A
S
T
MASTER R
T
SLAVE
ADDRESS
BYTE ADDRESS
a 15 ? a 8 a 7 ? a 0
S
T
A
R
T
SLAVE
ADDRESS
DATA
S
T
O
P
SDA LINE S
S
P
A
C
K
A A
C C
K K
Figure 11. Selective Read Timing
A
C
K
N
O
A
C
K
BUS ACTIVITY:
MASTER
SLAVE
ADDRESS
DATA n
DATA n+1
DATA n+2
DATA n+x
S
T
O
P
SDA LINE
P
A
C
K
A A
C C
K K
Figure 12. Sequential Read Timing
A
C
K
N
O
A
C
K
http://onsemi.com
8
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CAT24M01YI-GT3 IC EEPROM SRL 1MB I2C 8TSSOP
CAT25010LI-G IC EEPROM 1KBIT 10MHZ 8DIP
CAT25020VE-GT3 IC EEPROM 2KB I2C SER SPI 8SOIC
CAT25128XI IC EEPROM 128KB SPI SER 8SOIC
CAT25160HU4I-GT3 IC EEPROM SRL 16KB I2C 8UDFN
CAT25256XI-T2 IC EEPROM 256KBIT 10MHZ 8SOIC
CAT25320LI-G IC EEPROM 32KBIT 10MHZ 8DIP
CAT25512HU5I-GT3 IC EEPROM SRL 512KB I2C 8UDFN
相关代理商/技术参数
CAT24M01XI-T2 功能描述:电可擦除可编程只读存储器 1MB I2C SERIAL 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24M01YI-GT3 功能描述:电可擦除可编程只读存储器 1MB I2C SERIAL 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24M01YI-GT3JN 功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24S128C4ATR 功能描述:IC MEM EEPROM 128KB I2C SOT563 制造商:on semiconductor 系列:* 零件状态:有效 标准包装:5,000
CAT24S128C4UTR 功能描述:IC MEM EEPROM 128KB I2C 制造商:on semiconductor 系列:* 零件状态:在售 标准包装:5,000
CAT24S64C4ATR 功能描述:IC MEM EEPROM 64 KB I2C 制造商:on semiconductor 系列:* 零件状态:在售 标准包装:5,000
CAT24W02JI/EEP 制造商:Catalyst Semiconductor 功能描述:ELECTRONIC COMPONENT
CAT24W64JITE13 制造商:CATALYST 功能描述:*